مشخصات فنی رنگ کولتار اپوکسی دو جزئی به شرح زیر میباشد
Two Pack Coal Tar Epoxy 439
Description
Two pack polyamide cured coal tar epoxy
Recommended Use
Hard wearing , good resistance to crude oil, sea-water, ballast water tanks, alkaline and submerged surfaces
Surface Preparations
Blast cleaning to min. Sa. 2.5 or power tool cleaning to St.3 and free from oil or grease and other contaminations
Substrate/Primer Required for Two Pack Coal Tar Epoxy
Blast cleaned steel or shop primed surfaces
Topcoat Required
Normally none
Solid Volume: 65±2%
Recommended Film Thickness: Wet 195, Dry 125 microns
Theoretical Coverage: 5.2 m2/lit
Color: Brown and Black
Gloss: Semi-matt
Flash Point: 28°C
(Mixed) Specific Gravity: 1.45 g/cm3
Mixing Ratio: 4:1 By Volume
Mixing Instruction: Mix thoroughly before use
Pot Life: 8 hours at 20 °C and less at higher temp
Spraying Thinner: T-41
Airless Spraying Conditions
“025.-021. | Nozzle |
165kg/cm2 (2350 psi) | Pressure |
Application Conditions Two Pack Coal Tar Epoxy
Max |
Min |
|
50°C |
10°C |
Surface |
50°C |
10°C |
Ambient |
75% |
0% |
Humidity |
Drying Times At DFT [125] Microns
Hard Dry | Touch Dry | |
10days |
5hours |
10°C/60RH |
6days |
3hours |
20°C/60RH |
5days | 2hours |
30°C/60RH |
Recoating Interval
Max | Min | |
6days | 24hours | 10°C/60RH |
4days | 16hours | 20°C/60RH |
2days | 12hours |
30°C/60RH |
Storage Conditions
Can be stored at least one year in original pack and in a dry and cool conditions (below 35 °C)
Safety Instructions
Take normal precautions and proper ventilation while applying paint in a confined areas
Note
Use brush or roller for small areas and touch ups
Supplied technical information is based on our laboratory and practical experiences. As the products are often being used under conditions beyond our control, we only guarantee for the quality of our paint itself
جهت خرید رنگ کولتار اپوکسی دو جزئی کیمیاهمرنگ با ما تماس بگیرید.
Two Pack Coal Tar Epoxy
شرح محصول:
رنگ اپوکسی کولتار دو جزئی با هاردنر پلیآمید
موارد مصرف:
یک پوشش سخت با مقاومت خوب در مقابل
- آب دریا و آبهای غیرآشامیدنی
- نفت خام
- مواد قلیایی
رنگ کولتار اپوکسی دو جزئی مناسب برای پوشش داخل مخازن آب و سازههای زیرآب است.
آماده سازی سطح زیر کار:
سطوح مورد رنگ آمیزی بایستی عاری از هرگونه آلودگی باشد و تا درجه sa2 1/2 سندبلاست و یا تا درجه st3 به وسیله فرچه های سیمی تمیز نمایید.
آستر مورد نیاز :
روی سطوح سندبلاست شده و یا پرایمر زده شده، اعمال گردد.
رنگ رویه پیشنهادی:
معمولا نیازی به پوشش بعدی ندارد.